Monday, August 26, 2013

Waves Punch Back

One of the phrases I use to describe sea kayaking is, "we punch holes in waves". While most of the time it's more accurate to say that we glide up and over waves, or edge into them and let them roll underneath, when it gets choppy there are plenty of times when the bow will just poke right into an oncoming wave, like a knife into a balloon.

Yesterday, paddling the trail from Inwood down to Pier 96, some headwinds kicked up some nice waves for a bit. Sure enough, the Argonaut punched right through them.

One one wave though, I watched the water run up along the foredeck and ramp up the slope of the cockpit - splashing right into my eyes. So, I won't be taunting the water any time soon. It fights back.

Wednesday, August 21, 2013

Winter Skeg Repair

Last summer, and again in the fall, I replace a kinked skeg cable on my own boat, a VCP Argonaut. While there was a fair amount of detail, once I learned the basic mechanism of a skeg, it was very straightforward: loosen two screws, essentially, and pull the bad cable; put in the new cable, trim to fit, and then tighten the screws. Voila, repair complete.

Thus, under the rubric of, "a little knowledge is a dangerous thing", I offered to repair the skeg cable on one of my club's older boats, a plastic WS Tempest 170. What could go wrong?


I thought it would be helpful to write up details of that repair, for my own review as well as an informational to others (whether a warning, or a guide, actual mileage may vary). I also feel like I owe an explanation to some of my fellow clubmates, on why something so simple dragged on for months.  While in retrospect, it was ultimately a simple repair, the entire effort was confounded by weather, mistakes, and some additional components that required repair.

Additionally, In my day job, I work as a systems engineer, and when something goes wrong, we always review and document what went wrong in order to learn from it: how the problem can be prevented, and more quickly resolved, in the future. I and those who assisted me learned a lot from this repair, and hopefully, the complexity we encountered here won't deter us from future attempts at reviving our fleet.

Where possible, I've added photos and video.

I also want to put in a few good words about Tom Holtey at Tom's Top Kayaker Shop in New Hampshire. I first found Tom's shop when I needed to replace the day hatch cover on my VCP Argonaut, and I turned to him again for my own skeg cable repair (and again, when I kinked it by sliding the control knob against a support beam while pulling the boat out). Tom was a great help in researching some of the more picayune details of this repair, and easy to work with when I needed to return a part and order another. I got nothing but fair and square dealings from him, and recommend him for advice and guidance on kayak repairs.

The Issue:
Skeg cannot be lowered using the control mechanism. The skeg can be forcefully pulled down about three-quarters of the way, and can be pulled up to the one-quarter mark using the control mechanism, but otherwise is not functional.

Initial Assessment:
Assessment occurred in two phases, as more elaborate disassembly was required to ascertain the secondary issue. The primary issue was that the skeg cable was kinked near the rear, a common issue for skegs that occurs when the weight of the boat rests on a deployed skeg, i.e. someone forgot to retract it before pulling it out of the water. The secondary issue was that the sliding control rod, which is where the front of the cable goes, was slightly bent, and not moving straight; hence, even with a good cable, full control could not be restored until the rode was replaced.

Proposed resolution:
Replace the cable and the control rod.

For reference, here is a video of how to repair should go. The skeg blade in the video is the kind that we were dealing with - a detail that would become important later.

Aso for reference, here is a picture of how I dis-assembled the control mechanism on my own boat. I find this part to be the most difficult to explain to people. The only key difference is that the Tempest used a larger Phillips-head screw instead of a hex screw.

In the picture above, I've loosened the control knob to slide it over. You can see the skeg cable inside the control rode, through the hole between the two black markings where I had pre-marked the edges of where the knob should return to. In operation, the knob sits between those two marks, and the screw presses down on the cable, securing it. When you move the knob, the control rode and cable move with it. The knob does not slide along the tube.

Obstacle 01: Severely corroded cable and attach points hinder removal of the cable.
The first part was: there was a lot of corrosion on every metal piece involved. Detaching the cable from the blade itself was easy enough, but loosening the screw that holds the control knob fast was very difficult. Removing the cap at the fore of the cable tube was difficult, and was only made possible by later removing the entire assembly - which was also a chore. The control rod was slightly bent, hampering removal, and the cable itself could not be detached from the rod. Ultimately, I pulled the cable through the rear part of the way, cut the conduit, and then pulled it forward. That was easier than trying to get the rod through the fore or the aft. I would also end up replacing the set screw months later, when I realized it too was too corroded to be useful.

Here is a picture of the control rod, slightly bent. This was going to have to be replaced. I never did get it to detach from the cable, even after completely removing it.

For example of corroded metal, here is the aft end of the conduit. Simply disconnecting it was a huge challenge because the nut that held it in place was rusted together with the bolt, and at an odd angle to work with. This is actually one of the prettier-looking components.

Obstacle 02: Incorrect cable ordered.
This was an easy mistake. The cable repair kit is listed as a single kit, but on the order page, there are different SKUs for different model boats. If no selection is made, the first option - for a WS Tempest 165 - is entered. When I ordered, my eyes went to 'add to cart' first, and thinking there was one kit for all, I got the default kit. I wouldn't figure this out till I got stuck deciphering the instructions.

Here is a picture of our skeg. In the background, you can see the picture from the instructions.

On our skeg, the bottom edge of the blade is here on the left, and the top is on the right. The cable comes in from the top of the blade into the empty square, where the "set screw" sits (see below). The kit that I ordered was for a newer model Tempest, where 1) the cable comes in at the middle of the top edge, and 2) is held in place by a swage integrated with the cable, rather than a set screw.

Obstacle 03: Mismatch between skeg demonstrated in instruction set and actual skeg.
I didn't just order the wrong size (Tempest 165 instead of Tempest 170) - I ordered the "Premium Skeg Repair Kit", which is only for WS models from 2010 and later. The main difference is that the newer cables have an integrated cable swage (a block that holds the cable fast to the skeg). On the older models, they use what's called a "Cable Attachment Fixture with Set Screw", where instead of an integrated swage, the cable fits into a small brass block that has a 1/16' allen screw inside. I tried to make the cable work by snipping the swage and running it into the older brass set screw, but ultimately 1) the set screw needed to be replaced anyway and 2) the cable was too short because I had the wrong size.

Obstacle 04: Severely corroded cable set screw needed to be replaced.
This refers to the set screw described above. I was able to twist the old cable out of it, allowing me to remove the set screw. However, after some more close-up testing, it was clear the screw wouldn't tighten. It's hard to tell exactly what's wrong because it's an internal mechanism, but in and case, it wasn't going to hold the cable tight.

Here is the set screw, in place. You can see the cable coming down and entering the blade. The set screw faces after (the the right in the photo). However, we had to replace it as well.

Obstacle 05: Lost time attempting to fit cable and conduit to the incorrect part.
A lot of this experience was a learning process. I watched the videos, set aside tools, and the ran into, "hmm, it isn't going like it should". In some cases, this was due to screws and other fasteners that haven't been touched since the boat was built. In other cases, it was because of the wrong parts, or flat-out broken parts described above. I figure at least twelve to fifteen hours of effort were spent just trying to figure out what the heck was going wrong - and working just a couple of hours per weekend, with a wait of a week or so to get the next step figured out, that adds up to at least 4-6 weeks of lost time.

Obstacle 06: Lost time due to Hurricane Sandy, illness, and lost keys.
Similar to above, there were a few weekends where we didn't have access due in part to Sandy, and even when we did have access, there were a few weekends where everyone in our club was pitching in to clean up and then repair our facilities. I also caught a really bad cold that killed about two weekends in a row for me in February, and later, lost a set of keys that meant I had to coordinate access for a week or two while I got them replaced. That was probably the most frustrating period for me - the end was in sight, but all I all I could do was drink cough syrup and wait for keys. More than anything else though, working on this over the span of weeks rather than days meant having to get re-acquainted every time I came back to it.

Ultimately, I replaced the cable, cable conduit, control rod, and set screw. In so doing, I dismantled these components and also the fore tube where the rode slides into in the Up position. These efforts were hampered by corroded components, a bent control rod, irregular working conditions, and illness. However, once completed, the skeg is functional, fully capable of being extended and retracted fully from the cockpit.

Successful Repair Steps:
Ultimately, here's what happened, and which would have gone more smoothly given 20/20 hindsight (or is that foresight).

Remove the cable by detaching from skeg and disassembling forward tube at the start.
Order the  "Cable Attachment Fixture with Set Screw" for WS Tempest 170.
Order the replacement cable control rod.
Thread the cable from the after and control rod through the fore, and measure to fit.
Test mechanism and trim cable.
Attach set screw and control knob.

Mixed Company

We tried something interesting at the ranch today: taking SUP paddlers on a trip to Liberty Island.

SUP, or Stand Up Paddleboards, are a common site on the river these days. I'm surprised where I see them, but after today's trip, less so. We had a couple of experienced surfer/SUPers, and they did remarkably well. There were five kayaks, three guides and two clients, and we set out south from Pier 40, crossing just above Pier 26 to Jersey City, and then proceeded south past Morris Canal and Ellis Island.

It wasn't entirely without incident. At one point we paddled by a small heliport, and the prop wash knocked over one of the SUPers. They would have made it to Liberty if we had left sooner; as it was, by the  time we got to Ellis Island, the tide was coming in, and it proved insurmountable. I took the kayaks down to Liberty, we took a glance, and then paddled back to rejoin the SUPers and the guide who stayed with them.

However, that was already against a strong southerly headwind, and with a slightly late start the current turned against us by the time we reached Ellis Island. SUPers catch a lot of wind, given that they are standing. Even after dropping to a straddle position, they were paddling in place, so one of the guides took them to a small beach in Morris Canal while the kayaks pressed on. We got some nice sunset shots of Liberty before turning back.

Overall I was really impressed with the SUPers. The wake and wind waves we're accustomed to in the river were there, but weren't an issue for these guys. To be really, really clear: these guys went across the Hudson River standing up. I totally respect that.

Friday, August 16, 2013

Conditions After Work

I got a good paddle in with some new friends this evening, a trio of guys I've been wanting to paddle with for a while - V, I, and T. We set out south against the current, and with some wind, while commuting hours ferries crisscrossed. Lots of wake, including one unusually large wave that was easily six or more feet trough to peak. I thought it was going to curl over me but I got over it at the last minute.

Monday, August 12, 2013

Croton Camping Paddle

On the last weekend of July, I took off the following Monday in order to do some kayak camping with my friend MH. We've been meaning to do this for a while. We departed Inwood late Sunday morning and arrived at Croton Point in the evening; camped and hung out, then returned early Monday afternoon, arriving at Inwood as the sun set. It was a great trip.

We crossed the river to the west side and paddled up along the Palisades. We were a little concerned about the weather; there were even odds of rain, and radar showed a major weather front moving east from Ohio. However, as the day went on it also appear to be moving north, so we took our chances and simply enjoyed a cool day in place of the 90+ heat wave that had enveloped the city earlier in the week.

One of my goals for years has been to paddle to the Tappan Zee Bridge, just because it is such a recognizable waypoint. Here we approach the Tappan Zee; along the way we passed a friendly sailor who told us that Irvington, which we had passed already, was friendly to paddlers.

It was hard not to think of a sad story in the news the night before, wherein a bride and another in the wedding party were killed in a nighttime collision between a motorboat and a barge.

As we made our way up the river, we enjoyed generally benign conditions. There was hardly any traffic out, and wind was minimal. We had timed our trip to catch a fair amount of current, so even the paddling wasn't hard - all 5+ hours of it.

We stopped for lunch just above a lighthouse, landing on a small sandy shore. We had to move our boats a couple of times - we were there for less than an hour but the incoming tide threatened to float our boats away.

Lunch was just north of Tarrytown  Light - a retired lighthouse just north of the Tappan Zee. Our lunch spot was just around the bend below the wall in the photo above.

Eventually, we landed at Croton Point Park. We had paddled around trying to figure out the "Hudson River Water Trail" camping site, but as near as we could figure, that "campsite" was just sanctioned guerrilla camping. We found a spot, landed, and set up camp as the rain started to fall.

Here we have Camp MH (above) and Camp Cowgirl (below). The safety sawhorses turned out to be from some planned tree cutting we learned about the next day.

Since I set up my camp in the rain, I used my main towel to dry out my sleeping quarters. The next day I draped it over my boat.

I made the road my kitchen. I figured in the worst case, I wouldn't be able to burn the road down.

When we got ready to leave, I took time to repack my boat. I had a little less food and wanted to see if I could do a better job repacking. I did a little better but not a big difference.

When we were at Croton, I took some shots of the river. Above looking across Croton Bay.

Here, looking south from the southernmost part of Croton Point. The landscapes in this part of the Hudson River Valley are the same as the art style that it gives its name to. It is a dreamy horizon of sky, rocks, and river.

I didn't take as many photos - well, as many good photos - on the way back. We left early and crossed to the western side of the river, paddling down along parkland quite a ways. MH was scouting for possible future guerrilla campsites - though when we asked someone who was official-looking, he did say camping was prohibited.

On the way back, we paddled through a large marina (or two, it was hard to tell) in Nyack. I took a shot at rolling my camping-laden boat. I succeeded, if you count as success "I came halfway up and then high-braced before I rolled back in." I also noticed I had to adjust my sense of where to place the blade in part, as far as I could tell, because the drybag on my rear deck was pushing the boat up a when capsized.

We stopped at Piermont Pier on the way back for lunch - this is a long pier that extends out from Piermont, nearly halfway across the river and acting as a sort of marker to the lower end of the
"Tappan Zee." We rested, talked with another paddler, and then packed up for the final leg home.

There was quite a bit of wind from the west as we passed Piermont Marsh, and we charged past it to take windshade from the Palisades. The current went slack, and we picked up the pace. MH showed off his prowess, speeding ahead and waiting for me. We got home at dusk.

It took about six hours of paddling each way, plus an hour and a half rest, sometimes one stop, sometimes two. It was a pleasant paddle both ways, if a little windy on the way back. Total distance was about 46 miles, about 23 each way. I've paddled about 30-32 miles in a single day, but never such lengthy distances two days in a row.

It was good camping experience. I haven't camped in a long time, and never from a kayak. MH was a great mentor in this respect, and I hope to camp with him again some day.

A map of our route:

View Croton Camping 2013 Actual in a larger map